Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Blog Article
Listed here down the page you can locate lots of really good answers all about How to Install a Bathtub.
Mounting a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is readily accessible, the task can move easily; if you need to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you install a new tub in your restroom if you have actually already gotten a brand-new tub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools as well as product checklist must consist of the following:
Planning for the Installation
Firstly, the sustaining structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub till the level reads degree.
To install faucets, fit the bottom of the furthest flexible tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water as well as examine all joints and new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Secure the tap in place with the producer offered backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, leading to problems with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very enthusiastic about How to Install a Bathtub Yourself and I really hope you liked our entry. Those who appreciated our article please don't forget to pass it around. Thank-you for your time spent reading it.
Get Estimate Report this page